The Washington journey-level plumber exam (PL01): the complete guide

What the PL01 actually is

The journey-level plumber certificate is a credential issued by the Washington State Department of Labor & Industries (L&I). To earn it, you pass the journey-level examination — commonly called the PL01 — which the testing company PSI administers on L&I's behalf at test centers around the state.

It's a serious exam: three separately-scored portions in one sitting, all closed book, 70% required on every one of them. Here's the whole thing at a glance.

Eligibility: 8,000 hours before you can sit

Under WAC 296-400A-121, you may take the journey-level examination after completing 8,000 hours — and not less than four years — of documented training, which must include 4,000 hours of commercial plumbing experience under the direct supervision of a certified journey-level plumber.

You apply through L&I. Once your application is approved, it's good for one year — that's your window to schedule, sit, and pass. Let it lapse and you're reapplying (and re-paying).

What it costs

• $202.10 — L&I application and exam fee. Non-refundable, even if you never test.
• $80 — PSI's fee for the three-portion sitting. (PSI's single-portion retests are $50 per portion, but those only come into play from the fourth attempt — more on that below.)
• ≈$282 — realistic all-in cost of a first attempt.

The format: three portions, one sitting, 70% on each

You need 70% on each portion. Averaging doesn't help you: score 90-90-60 and you've failed. And on your first three attempts, failing any single portion means retaking all three. Only from the fourth attempt on do you retake just the failed portion.

Per L&I's advisory-board transcripts, the portion that most often sinks candidates is the waste & vent drawings — water-sizing pass rates run high by comparison. We wrote a whole guide on it: Waste & vent: the part of the exam most candidates fail.

Closed book — but a few tables are provided

You don't bring a code book. The exam does hand you a small set of reference tables:

• Table 702.1 — drainage fixture unit values
• Tables 610.3, 610.4, and 610.10 — used for the water sizing portion

What it does not provide is Table 703.2 — the drainage and vent sizing table your waste & vent answers depend on. Those maximum fixture-unit loads and vent lengths have to be in your head.

Which code? 2015 UPC + Washington amendments

Per L&I, the exam is based on the 2015 Uniform Plumbing Code with the Washington State amendments (WAC 51-56).

Yes — Washington adopted the 2021 UPC for installations back in March 2024, and no, the exam hasn't switched. You could be installing under one code edition at work and tested on another. If that sounds confusing, it is: we broke down exactly what to study in 2015 vs 2021 UPC: which code the exam actually tests.

Scheduling the exam

Once L&I approves your application, you schedule directly with PSI:

• Online at test-takers.psiexams.com/waplumb
• By phone at 855-746-8173
• To reschedule or cancel an existing appointment, the line is 855-340-3910 — don't mix the two numbers up.

Take the appointment seriously: missing it without rescheduling in time is treated as a failed attempt.

The 15 Washington test centers

PSI runs the PL01 at fifteen locations across the state:

If you fail: the retake rules

1. Wait 14 days minimum before retesting.
2. Reapply to L&I with a new, non-refundable $202.10 fee.
3. Attempts 1–3: fail any portion, retake all three (full $80 PSI sitting).
4. Attempt 4 and beyond: retake only the failed portion ($50 per portion at PSI).
5. Your approved application is valid for one year — repeated failures can burn through the window.

A realistic 8–12 week study plan

Most candidates study two to three months. Here's a structure that fits around a full-time work week:

Weeks 1–2 · Baseline and orientation

• Take a free practice test cold to find out where you actually stand.
• Map the 2015 UPC's layout — the exam draws on chapters 1–10 and 15–17. Learn where everything lives before you memorize anything.
• Read Chapter 2 (definitions) early. Stack vent vs. vent stack, developed length, indirect waste — the exam loves terms that sound interchangeable and aren't.

Weeks 3–6 · Chapter-by-chapter drills

• Work through the code chapters systematically: water supply and distribution, sanitary drainage, venting, fixtures, water heaters, traps and interceptors, indirect wastes.
• Drill the Washington amendments (WAC 51-56) alongside the base code — the exam is written for Washington, not for the model code alone.
• Keep a running list of every question you get wrong while feeling sure. Those are the ones that fail exams.

Weeks 7–9 · The drawing portions

• Commit Table 703.2 to memory — maximum fixture-unit loads and vent lengths by pipe size. The exam won't give it to you.
• Practice full waste & vent drawing exercises against the clock. This is the portion most candidates fail; give it the most reps.
• Run water-sizing exercises using tables 610.3, 610.4, and 610.10 — those are provided, so train on reading them fast, not memorizing them.

Weeks 10–12 · Simulate, patch, taper

• Take full three-portion simulations under real conditions: 90 minutes each, closed book, no notes.
• Spend the final days reviewing your miss list, not cramming new material.
• Confirm your appointment details with PSI, plan the drive, sleep.

PL01 FAQ

More free guides